Height-only size charts assume average proportions. Many women have longer legs and a shorter torso at the same height, so the frame that clears standover is too long to reach. This calculator sizes by stack and reach instead.
Your numbers
Enter your height and inseam to see your numbers.
How to measure
- Height: barefoot, back against a wall, a book flat on your head. Mark the wall and measure to the floor.
- Inseam: barefoot, feet about 6 in (15 cm) apart, back to the wall. Pull a hardcover book firmly up into the crotch, as firmly as a saddle would press, and measure from the floor to the top edge of the book. Repeat three times and use the largest value.
- Arm span: arms out level against a wall, measure fingertip to fingertip. A helper makes this much easier.
What stack and reach mean
Reach is the horizontal distance from the center of the bottom bracket to the top of the head tube. Stack is the vertical distance between the same two points. Together they describe how long and how tall the front of the frame is, independent of seat tube length or the letter on the size sticker. Two bikes labelled “Small” can differ by 20 mm of reach, which is a full stem size.
Seat tube length matters less than it used to: a seatpost adjusts saddle height over a wide range, while reach can only be corrected by about 20 mm with a different stem before handling suffers.
The formulas
saddle height = inseam × 0.883 (bottom bracket center to saddle top)
frame size = inseam × 0.665 road, gravel −1 cm
= inseam × 0.66 hybrid (converted to inches)
= inseam × 0.226 mountain (inches)
reach target = style baseline at 165 cm + slope × (height − 165)
− 4 mm for each 1% your inseam/height ratio is above 46%
+ 0.6 mm for each cm your arm span exceeds your height (±8 cm max)
stack target = style baseline + slope × (height − 165)
+ 7 mm for each 1% your inseam/height ratio is above 46%
max standover = inseam − clearance (2.5 cm road and hybrid, 4 cm gravel, 6 cm mountain)
The saddle height multiplier is the long-established 0.883 method. Baselines and slopes for stack and reach are editorial estimates set to sit in the middle of typical endurance road, gravel, fitness and trail geometry charts across sizes XXS to L, which is why the result is a range and not a single number. The proportion corrections shift the target toward a shorter, taller front end for riders with a long inseam relative to height.
When the standard calculation does not fit
You are between two sizes
Choose by reach. If the smaller frame’s reach is inside your range, take it and raise the saddle: a slightly longer seatpost and one more spacer under the stem are easy changes. Shortening a frame that is too long is not possible.
You are under 5′2″ (157 cm)
On 700c wheels the smallest frames run out of room: the front wheel gets close to your toes and designers steepen the seat tube or slacken the head tube to compensate. Frames built around 650b wheels in the smallest sizes avoid this. Use the small-frame bike finder to filter for them.
Racing position or limited flexibility
The targets describe an endurance position. For an aggressive race position subtract 15–20 mm of stack. If you have limited hamstring or lower-back flexibility, add 15–20 mm of stack and stay at the short end of the reach range.
Mountain bikes
Modern trail geometry is deliberately long in reach and paired with a 35–50 mm stem. Compare our target with the brand’s chart for your height rather than with road numbers, and give standover clearance priority.
Common measuring mistakes
- Using pants inseam. Trouser inseam is typically 2–3 in (5–8 cm) shorter than cycling inseam. This alone moves the result a full size.
- Measuring in shoes or with the book held loosely.
- Trusting the size label. A women’s S, a unisex S and a 49 cm from three brands are three different bikes. Compare stack and reach in millimeters.
- Fixing a long frame with a very short stem. Below about 60 mm on a road bike the steering becomes nervous. If you need that, the frame is too long.
Where to go next
These tools give starting points, not medical or professional fitting advice. Formulas and data sources are listed on this page so you can check the reasoning. Spotted an error? Tell us and we will correct it.
